Поиск продукции

 

 

THERMAL TOP P 300-FSC / RH1 / HONEY GLASSINE 65DFF/RH01/036415788158982

Download as pdf

Date07.05.2019 SI
ProductTHERMAL TOP P 300-FSC / RH1 / HONEY GLASSINE 65
Sales CodeDFF/RH01/03
EAN6415788158982
Product useProduct designed for topcoated direct thermal labels especially in pre-packed food applications with good convertability, high speed direct thermal printability and superb initial tack.
Typical technical values
FaceTHERMAL TOP P 300-FSC
ProductA top and reverse side barrier coated paper with a high sensitivity thermal coating produced totally without BPA-based chemistry. This face paper is made from FSC™-certified (mix credit) pulp.
Substance76g/m²ISO 536
Caliper75µmISO 534
Tensile strength MD4.7kN/mISO 1924-3min
Tensile strength CD2.3kN/mISO 1924-3min
Brightness87%ISO 2470
Imaging colourBlack
ScanningVisible red light (wavelength up to 650 nm).
DT printing speedDirect thermal printing speed up to 300 mm/s.
PrintabilitySuitable for direct thermal, UV- and water-based flexography, UV-letterpress and UV-offset.
SustainabilityThe product is sold as FSC™ Mix Credit under UPM Raflatac's FSC certificate SGSCH-COC-004879.
AdhesiveRH1
TypeGeneral purpose, strong permanent adhesive.
CompositionRubber, hotmelt.
Tack25N/25mmFTM 9
BackingHONEY GLASSINE 65
ProductYellow transparent glassine backing paper.
Substance57g/m²ISO 536
Caliper51µmISO 534
Tensile strength MD6.2kN/mISO 1924
Tensile strength CD2.3kN/mISO 1924
Transparency49%DIN 53147
Performance
Total caliper145 µm
Minimum labelling temperature-5 °C
Service temperature-40 °C to 50 °C
Shelf lifeFrom date of manufacture: 12 months, under FINAT defined storage conditions (+20-25°C and RH 40-50%). Prolonged storage at higher temperatures and/or humidity levels will shorten the shelf life.
Information
Product InformationDesigned for a wide range of industrial applications including pre-packed foodstuffs labelling where high speed direct thermal printability and premium resistance to oil or water are required. Recommended for use in cold environment, particularly if the application surface is moist or if very high initial adhesion is required. Very good adhesion to non-polar surfaces and pre-testing is required for adhesive surface printing. Pre-printing and varnish layers decrease print head heat energy conductivity into thermal layer, consequently it is recommended not to pre-print/varnish label area which is meant for direct thermal printing.
Approvals
Approvals and certificationsFor food packaging applications, please contact your local sales representative for the individual Declaration of Conformance (DoC) document of each product component for further compliance information.
DisclaimerThe performance of the product should always be tested in the actual application conditions. Our recommendations are based on our most current knowledge and experience. As our products are used in conditions beyond our control, we cannot assume any liability for damage caused through their use. Users of our products are solely responsible that the product is suitable for its intended application, and have determined such at their sole discretion. Users must comply with any applicable legislation and/or testing requirements for the finished article, and are responsible for bringing their products to market. This publication does not constitute any warranty, express or implied, and is intended only for the recipient and cannot therefore be transferred to any third party. We cannot assume any liability for the use of our products in conjunction with other materials. All our products are sold subject to UPM Raflatac’s general sales conditions, and you should ensure that any existing laws are observed. This publication replaces all previous versions. All information is subject to change without notice.

 Наличие материала

ServiceWidth (mm) / Length (m)
Stock2000/0

 Наши сервисы?

 Компоненты

 ‭(Hidden)‬ Новости

 ‭(Hidden)‬ Брошюры

 ‭(Hidden)‬ Материалы по теме